top of page
Search

Building the Two Inch Focuser: Notes From the Bench

Oct 22
3 min read

Updated: 17 hours ago

Back in August I wrote about how our two inch focuser performs under the stars. Since then, lots of you have asked what it's actually like to build one. So this one is for the builders: what to watch for at the printer and on the bench, and a few of the design tricks hiding inside.

If you want the whole design story, from shrinkage to support sleeves, I wrote that up over on our sister site, Tundra 3D.

Start With a Calibrated Printer

Your eyepieces and cameras are machined metal, and they won't meet a printed part halfway. The drawtube's bore is only about a tenth of a millimetre bigger than a two inch accessory, and the 2" to 1.25" adapter is just as tight.

So before you print a single focuser part, calibrate for shrinkage, and dial in your X/Y hole and contour compensation and your elephant's foot compensation. Expect some trial and error. The right numbers move around with humidity and with filament colour and type.

The Drawtube Prints Upside Down

When you open the drawtube and adapter files, they'll look upside down, with the flange at the top. That's on purpose. It keeps the surfaces your accessories touch away from the bed, where elephant's foot would make them too tight.

The support is built right into the file: a hollow sleeve around the part, with a gap of about half a millimetre. No slicer supports needed. When it's done printing, gently tap a thin blade into the gap and work your way around until the sleeve lets go.

The inside drawtube in the slicer, cut in half with the flange end up, showing the hollow built-in support sleeve and the thin gap
The inside drawtube in the slicer, cut in half. The hollow wall with the pointed roof is the built-in sleeve holding the flange up, and the hairline beside it is the gap you tap the blade into.

Check Your Gears Before You Build

The fine focus knob holds two stages of herringbone planetary gears, 9:1 in total, and each one prints in place in one piece. A 0.2 mm nozzle makes a big difference here.

CAD render with the fine focus knob made see-through, showing the herringbone planetary gears inside
The fine focus knob, see-through. The herringbone planetary gears live inside.

Give every gearset the flick test before it goes in. Set it lightly on the fine focus knob and flick the outer ring. If it keeps spinning a little after your finger leaves it, it's good to go.

Close, but not quite there? Break it in:

  • By hand. Leave it on the fine focus knob and spin it while you watch a movie.

  • With a drill. Put the shaft of the transfer plate in a drill, slide three 3 mm × 16 mm dowel pins through it into the three planet gears, and run it to wear the gears in. Be careful not to hurt yourself, and go slowly.

  • A little PTFE lubricant helps either way.

Setting the Tension

The two screws under the drive shaft set how hard the shaft presses on the drawtube. Too loose and a heavy camera will slip. Too tight and focusing gets stiff.

Those screws thread into M3 nuts that drop into slots deep inside the focuser body. That's on purpose too. Heat-set inserts would get pushed right out of the plastic under that much load. And the screws push on a 6 mm magnet in the bottom of the plunger rather than on the plastic, so they can't dig in as you tighten them.

Cross-section through the focuser body showing an M3 nut in a side slot, a screw pushing on a magnet in the plunger, and a PTFE half-pipe cradling the shaft
Cut through the body (purple). The nut (light blue) slides in from the side, the screw pushes on the magnet (green), and the plunger presses the PTFE half-pipe (yellow) against the shaft.

The finished focuser has to pass the same test as every one we build: drawtube pointing straight up, holding 1 kg without slipping.

Tilt and Autofocus Ready

Heat-set inserts still have their place. The grub screws for tilt adjustment each sit in one, so you can square the focuser up with your optics. And a pair on the side of the body is ready for you to bolt on an electronic autofocuser (EAF).

CAD render of the focuser from the front, showing the tilt grub screws and two brass heat-set inserts for an autofocuser
The tilt screws (copper) around the drawtube, and two brass inserts on the body for an autofocuser.

Watch the Full Build

The files are free on our GitHub. Questions about building a focuser? Ask on our Discord.

 
 
 

Comments


bottom of page