top of page
Search

Striking Back at Dew: Our Heater and Fan Controller

Mar 20
3 min read

Updated: Oct 30

Thermal image of the dew buster cord glowing in a 200mm mirror cell
A thermal camera view of the dew buster cord warming the back of the primary mirror.

Last summer I lost a battle with dew, and I wanted to strike back.


The goal was simple: a totally affordable and effective way to control dew and tube currents on our Skyward telescopes. It took a few rounds of experiments, a thermal camera and a handful of very inexpensive parts.


Why Dew Forms


On a clear night, your telescope is losing heat to the sky. The mirrors radiate their warmth straight up into space, and they can end up colder than the air around them. When a surface drops below the dew point, the moisture in the air condenses on it, just like water on the outside of a cold glass. On a telescope, that surface is your mirror.


There is a second problem that works the other way. A mirror that is warmer than the air releases that heat slowly, and the warm air rising off it makes the view shimmer, like looking across a hot road. These are called tube currents.


So we want two things: enough gentle heat on the optics to keep them above the dew point, and a way to move air through the tube so the mirror is not making its own heat shimmer.


Heat Where It Counts


Most dew heater solutions for Newtonian telescopes have to heat the mirror cell and its housing first, before any of that heat reaches the mirror. That is a lot of plastic and metal to warm up just to get to the glass.


Our approach is a "dew buster cord": nickel chromium wire inside a fibreglass jacket, lightly pressed against the back of the primary mirror. The heat goes straight into the glass.


Dew heater cord looped in a mirror cell next to a multimeter
Bench testing bargain basement dew heater materials.

In February I tested some bargain basement materials on the bench. At full throttle, it was using about 5 Watts with those particular choices. The thermal camera showed exactly where the heat was going.


Thermal image of the heater cord in the mirror cell during bench testing
The same test through the thermal camera.

Then I designed a new 200mm mirror cell with a channel that guides the cord in a loop behind the mirror, so it sits in the same place every time. That is the shape you can see glowing in the photo at the top of this post.


The secondary mirror gets its own heater too: a small 12V silicone rubber heating pad, 50mm by 50mm. The secondary mount has a recessed area where the pad sits out of the way, plus channels for zip ties, so the heater is secured cleanly with nothing flapping around in the light path.


Thermal image looking into the front of the tube with the secondary heater on
Looking into the front of the tube: the secondary heater glowing behind the spider.

Thermal image looking down the tube outdoors with the secondary heater on
Outdoors on a cool night, looking down the tube with the secondary heater on.

The Fan


The fan is an ordinary 80mm by 25mm 12V brushless fan, the kind used to cool computers and electronics, and it lives in the rear mirror cell cap. It pulls air in through the front of the tube, down past the primary mirror and out the back. That keeps air moving through the optical tube so the mirror can settle to the night air temperature instead of sitting in a pocket of its own warm air.


Three Knobs


The last piece was control. I did not want an expensive controller, so I used three inexpensive PWM motor speed controllers, the kind you can find for a few dollars each.


PWM stands for pulse width modulation. The controller switches the power on and off very quickly, and the knob sets how much of the time it is on. Turn it up and the heater gets more power. Turn it down and it gets less. The same trick sets the speed of the fan.


Each one gets its own knob, so the primary heater, the secondary heater and the fan are all set independently. They live in a 3D printed housing on the telescope, labelled Pri, Sec and Fan, so there is no guessing in the dark.


3D printed controller housing labelled Pri, Sec and Fan
The printed controller housing: one knob each for the primary heater, secondary heater and fan.

The secondary heater pad, the fan and each of the three controllers cost only a few dollars apiece. That was the whole point.


Cable management is one of the hardest parts of rigging up an imaging telescope. Having the controls built onto the scope keeps everything organized.


Thermal image of the heater cord warming in the cell with a controller board beside it
An early test: the cord warming in the cell, with a controller board beside it.

Get the Files


The printed parts are free on our GitHub, in the Skyward 200 Astrograph files: the dew and fan controller mount, the controller back covers and the 200mm mirror cell.



Questions about dew control? Ask on our Discord.

 
 
 

Comments


bottom of page